Omega WI8XX-U User Manual

User’s Guideomega.come-mail: [email protected] Latest Product Manualsomegamanual.info®®Shop on line atwiSeriesMain MenuCHART(2 Seconds/Div)1 Minute1 M

1.3 Description (continued)DATALOGGING: The OPC Server software makes it easy to integrate the wiSerieswireless sensor system with many popular Data

5PART 2HARDWARE2.1 Physical Characteristics and Mounting2.1.1 Front Panel Figure 2.1 Front Panel Display Table 2.1 Front Panel EnunciatorsFor comp

2.1.2 Rear PanelThe rear panel connections are shown in Figure 2.2.Figure 2.2 Rear Panel Power and Output ConnectionsTable 2.2 Rear Panel Connector

2.1.3 DimensionsFigure 2.3 Mounting Dimensions3.780 [96.00]1.890[48.00]0.700 [17.78]4.325[109.85]12CF12%RHD12CFPANEL THICKNESS0.25 (6.4) MAX0.03 (0.

2.1.4 Assembly and Mounting2.1.4.1 Panel Mounting Instruction1. Using the dimensions from the panel cutout in Figure 2.3, cut an opening inthe panel

2.1.4.2 Antenna Mounting InstructionFor best reception: connect the antenna directly to the rear of the meter, if themeter is not installed in a meta

2.1.4.3 Disassembly InstructionIf necessary, the board assembly may be removed from the front of the casehousing.Warning: Disconnect ac power from t

2.1.5 Electrical Installation2.1.5.1 Power ConnectionsWarning: Do not connect ac power to your meter until you havecompleted all output connections

2.1.5.2 Wiring OutputsThis meter has two factory installed outputs. The SPDT Mechanical Relay, SPSTSolid State Relay, Pulse and Analog Output Connect

2.1.5.2 Wiring Outputs (continued)Figure 2.9 Typical ApplicationsTEMPERATURECONTROLLERCONTROLSIDEdc INPUTSSRac INPUTSSRac INPUTSSRLOADSIDEHEATERVacV

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.OMEGA is constantly pursuing certification of its pro

2.1.5.3 Jumper Settings for Display Color SetupTo change the color of the lower display follow the instructions below: 1.The unit should be removed f

2.1.5.4 Dip SwitchesTo change the DIP switches, follow the instructions below: 1.The unit should be removed from the panel and opened. Refer to Secti

2.2 Network Communication Interfaces2.2.1 10Base-T RJ-45 PinoutThe 10BASE-T Ethernet network (RJ-45) system is used in the Meter fornetwork connectivi

PART 3NETWORK CONFIGURATION3.1 Ethernet (MAC) AddressMAC (Media Access Control) address is your computer's unique hardwarenumber. When you'

3.3 DHCP (continued)The Meter is shipped with DHCP disabled (factory default).If fixed or static IP address is desired, the DHCP must be disabled.The

3.5 IP AddressEvery active device connected to the TCP/IP network must have a unique IPaddress. This IP address is used to establish a connection to

3.5.2 Changing TCP/IP Properties on Your ComputerGo to your computer’s Control Panel then Network Connections. Pick the network with the proper Ethe

PART 4NETWORK OPERATIONSThis Meter can be used and configured in several ways, depending on user’spreference and network setup. It can be configured u

4.1 iConnect SoftwareThe Meter may also be assigned an IP Address by using the iConnect software.a) Download the iConnect software from the website l

4.1 iConnect Software (continued)d) To access the Wireless System for Configuration:Click on the "View Webpage" button, you will access the

iTABLE OF CONTENTSPart 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11.1 Safety Consider

4.2 Setting a New IP Address over the NetworkBesides using the iConnect software, you may use the Meter’s default IPaddress to access it and assign a

4.3 Meter’s Configurations and OperationsUsing a web browser, you should be able to view the Meter’s homepage.• Start your web browser.• From the bro

4.3 Meter’s Configurations and Operations (continued)Figure 4.6 LOGIN and ADMINISTRATOR PasswordsThere are 2 different access levels:1. ADMINISTRAT

4.3.2 Get Readings from the End DeviceOnce you see the End Device’s LED blinking periodically, it means it is sendingdata which will appear on the &q

4.3.2 Get Readings from the End Device (continued)ID: End Device ID/addressSequence: Sequence number [0-255 ].The Sequence number is incremented fo

4.3.3 Java Runtime Environment SetupIf your computer does not have Java installed, please download fromjava.sun.com. You can change the Java setting

For Java 1.6.x.x it is similar to Java 1.5.x.x but there is no need toremove CACHE.4.3.3.2 Java Runtime Environment 1.4 Setup Instructions1. Go to yo

4.3.3.3 Browser Proxy SelectionAccessing Meter units within your internal network• Usually when the computer and Meters are on an internal network, y

4.3.4 Java PolicyTo activate data logging and save graphs from the Java applets, it is necessaryto create a Java Policy file and copy it onto a folde

4.3.4 Java Policy (continued)5)Change Java Applet’s Runtime Parameters found on the following path:a. Control Panel --> Java --> Java Control P

4.3.7 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .384.3.7.1 Input . . . . . . . . . . . . . . . . . .

4.3.5 ChartClick on from the Home Page, the following page will appear. The Java™ Applet graph displays Process Temperature and AmbientTemperature.

4.3.5 Chart (continued)Title: Meter’s name, assigned in "Network Setup" page.Save Current Graph: Save the current graph in PNG (Portable Ne

4.3.6 Controller SetupThe Meter has two modes of operations. One is through the Front Panel Buttons(please refer to Front Panel Supplement for more d

4.3.6 Controller Setup (continued)Below are the definitions of terms used in the Controller Setup page.A) Setup:Clicking on the options shown, allows

4.3.7 SetupThis section is used to configure the Meter online. Click on the specific settingsto change the parameters on that section4.3.7.1 Input Con

4.3.7.2 Setpoints & On/Off ControlAuto Setpoint Deviation: If "enabled", allows changes to Setpoint 1 to bemade automatically to Setpoi

4.3.7.2 Setpoints & On/Off Control (continued)Figure 4.16 Setpoints & On/Off ControlSetpoint 2Permanent Store100DeadBand DeadBand On/Off 1On

4.3.7.3 Alarms 1 & 2Alarm 1 (or 2) Relay: to enable or disable (no alarm function) the alarms .Alarm 1 (or 2) Low: editable box for the low alarm

4.3.7.3 Alarms 1 & 2 (continued)Figure 4.17 Alarms 1 & 2NormallyAlarm at Power On: Alarm could betriggered immediately by non-controlling end

4.3.7.4 Analog Output RetransmissionThis menu will appear only if you have the Analog Output Option installedin your Meter.Figure 4.18 Analog Output

Figure 2.1 Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Figure 2.2 Rear Panel Power and Output Connecti

4.3.7.5 DisplayThis submenu allows the user to select the color of the display--green, red,amber.Screen Update: Editable box to enter the display time

4.3.7.5 Display (continued)This version of the menu will appear only if you have the Analog OutputOption installed in your Meter.Figure 4.19b Display

4.3.7.5.1 Display Color ExamplesExample 1:Output 1 & Output 2= SSRAlarm Setup: Absolute, Above, Alarm 2 HI Value "AALLRR..HH" = 200, Al

4.3.7.5.1 Display Color Examples (continued)Example 3:Output 1= Relay, Setpoint 1 = 300,Output 2= Relay, Setpoint 2 = 200Alarm 1 & 2 Setup: Devia

484.3.7.6 Passcode IDTo prevent unauthorized tampering with the setup parameters, the Meterprovides protection by requiring the user to enter the ID C

4.3.8 Network SetupClick on from the Home Page, the following page will appear. Figure 4.21 Network Setup Remote IP AddressRemote Port0.0.0.002000Re

4.3.8 Network Setup (continued)A) GeneralSecured Applet: If checked, the LOGIN password is required to open"Readings" and "Chart"

4.3.9 End Device SetupClick on from the Home Page, the following page will appear.Figure 4.22 End Device Setup Main MenuUpdateReadingsChartEND DEV

524.3.9 End Device Setup (continued)The End Device Setup Page is for configuring the End Device parameters suchas Name and Update Rate. #: End Device

534.3.9.1 End Device Parameters (continued)Figure 4.23 End Device ParametersRemote Display Format:Remote End Char(Hex): 0x 0000000F0DOffset(xxxx): C

ivFigure 4.26 HTTPget Example of Polling End Device . . . . . . . . . . . . . . . . .59Figure 4.27 ARP Commands and Responses . . . . . . . . . .

544.3.9.1 End Device Parameters (continued)Update (Seconds): How often this End Device is sending its data to the Meter.The default shown "updat

554.3.9.1 End Device Parameters (continued)If the end character for instance is 20 (Hex representation of space), the data willthen appear as: T75F T

564.3.10 Access Control (continued)Login Password: This allows users to access and modify all of the WirelessSystem Home Page menu items, except &quo

4.4 Telnet SetupIn the "Network Setup" page, under the Terminal Server section, set the TCPConnections to 1 to 5 other than 0, and use a te

584.5 HTTPget ProgramThe Httpget software is used to send a single HTTP or TCP request to the Meter.In contrast, the telnet or Hyperterminal programs

59where:-r –S are parameters needed for the the command stringCommand (See Table 4.1)192.168.1.135 is an IP address 2000 is a socket port number-C1 c

604.6 ARP ProtocolARP is the Internet layer protocol responsible for matching or obtaining the MAC(hardware) address that corresponds to a particular

614.7 iLog SoftwareThis is an Excel application software that can log temperature from the Meterover the local network (Ethernet) or the internet. a)

624.7 iLog Software (continued)Table 4.3 iLog Excel ApplicationsThe iLog application actually consists of several Excel files, though mostsupported

634.8 Mail Notifier SoftwareFor complete information of how to use the Mail Notifier software, click on theHelp menu of the main window.The Mail Noti

PART 1INTRODUCTION1.1 Safety ConsiderationsThis device is marked with the international caution symbol. It is importantto read this manual before ins

644.8.2 Program Options Setup and ConfigurationComplete program setup requires: • Entering a recipient for the email• Specifying connection details t

654.8.3 Device Setting and ConfigurationThe Meter and End Devices should first be configured and ready to use. Make sure to have the following settin

664.8.3 Device Setting and Configuration (continued)Figure 4.31 Mail Notifier Device Setting 4.8.4 Sending Txt Messages to a Cell PhoneOnce you ins

67Part 5 ENVIRONMENT / OPERATING CONDITIONSThe End Device and Meter are designed to be fixed mounted and operated in aclean and dry environment. Care

687. Where possible, try to ensure an uninterrupted line-of-sight betweennodes. Avoid obscuring objects (e.g. metal pillars, posts, sign) near theante

695.2 With Line-of-SightWhen installing the Meter it is important to position your device in such a way tooptimize the antenna location within what’s

705.3 Without Line-of-SightWhen line-of-sight is not possible, signal penetrates and is reflected by differentobjects to reach the destination. Ther

71PART 6SPECIFICATIONS ON/OFF CONTROL OUTPUT 1 & 2Relay: 250 Vac or 30 Vdc @ 3 A (Resistive Load), SPDTSolid State Relay (SSR): 20 to 265 Vac @

72GENERALConnection: Screw terminalsLine Voltage/Power: 90 to 240 Vac +/-10%, 50 to 400 Hz*; 110 to 375 Vdc, equivalent voltage; 5 W* No CE complianc

73WIRELESS COMMUNICATION (continued)Radio Power Output: 100 mW (20 dBm), 10 mW (10 dBm)Limitations on Equivalent Isotropic Radiated Power (EIRP) leve

1.2 Before You BeginInspecting Your Shipment:Remove the packing slip and verify that you have received everythinglisted. Inspect the container and eq

74PART 7FACTORY PRESET VALUESTo set the Wireless and Ethernet settings back to Factory Default do thefollowing to the DIP switches (see Figure 2.11).T

75Table 7.1 Factory Preset Values (continued) Setpoints & On/Off ControlAuto Setpoint Deviation Disabled CSetpoint 1 0 CSetpoint 2 100 CPermanent

Table 7.1 Factory Preset Values (continued) Analog Output RetransmissionRetransmission Enabled CVoltage/Current Voltage CInput Low 0 COutput Low 0.00

Table 7.1 Factory Preset Values (continued) End Device Setup-E WEC E E WWID Name Update Network Units Remote Format End Char Display Alarm1 ABCDEFGH 1

78APPENDIX A GLOSSARYUser of this manual should be familiar with following definitions:ARP (Address Resolution Protocol) is a protocol for mapping an

Appendix B IP AddressAn IP address is a unique 32-bit address assigned to a computer and includes:• A network ID number identifying a network.• A hos

Appendix C IP NetmaskIP Netmask or Subnet Mask is a 32-bit pattern of ones and zeros used to determinenetwork portion of an IP address from the host

Appendix D ASCII ChartASCII Dec Hex Binary ASCII Dec Hex BinaryChar No Parity Char No parityNUL 00 00 00000000 @ 64 40 01000000SOH 01 01 00000001 A 6

Appendix D ASCII Chart Continuation/ 47 2F 00101111 o 111 6F 011011110 48 30 00110000p112 70 011100001 49 31 00110001q113 71 011100012 50 32 00110010

Appendix E iLog Error MessagesError # Description Note-8003 User stopped logging readings.-10005 Failed to find the Meter. Ethernet cable is disconne

1.3 Description (continued)The wireless sensors transmit up to four hundred feet 400’ (approx. 120 meters--without obstructions or interference) to a

84Appendix F Warnings and Regulatory Information (continued)The following alert sign indicates that there are restrictions on usage of theequipment

WARRANTY/ DISCLAIMEROMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of one (1) yearfrom the

M4648/1110Where Do I Find Everything I Need forProcess Measurement and Control?OMEGA…Of Course!Shop on line at omega.comTEMPERATURE Thermocouple, R